I have attached my new ASA 5505 to my computer with the network cable as described in section 5. I have verified that Firefox 3 has both Java and Javascript enabled. When I enter it times out with no connection. I haved attempted to access it by connecting it to our LAN, then browsing it from various computers, both Linux and Windows.
Connect to and manage cisco firewalls, via console cable, telnet web browser and ssh. Cisco ASA Remote Management via VPN. By default PuTTy will connect with the correct port settings, if you want to change the settings see the option. The ASA ships with a default configuration that includes two preconfigured networks. Inside Network Interfaces.
It always times out. I have pressed and held the Reset button and tried again. The front and rear lights appear to indicate a proper connection, complete with activity. Can you give me a hint as to what I have done wrong or should do differently or in addition?
I'm not sure what the default address is, but your ASA should have come with a rollover cable. (It's a light blue, flat cable with an RJ45 connection on one end and a serial (DB9) connection on the other.) I would connect this directly to the ASA on the console port. Open hyperterminal up on your PC, and select the appropriate com port. The settings for Hyperterminal connection should be: Baud Rate: 9600 Data Bits: 8 Stop Bits: 1 Parity: None Flow Control: I leave default.
![Serial port adalah Serial port adalah](http://blog.router-switch.com/wp-content/uploads/2013/04/Cisco-asa.jpg)
After you click connect, you can hit enter a few times to get data on the screen. Once in, check your ip addresses in there by doing a: show ip address inside Once you have your IP address, you should be able to get into it. Also, make sure that your LAN is addressed on the same subnet as the ASA or you'll have to put a workstation in the 192.168.1.0/24 subnet. OK, here's what the book says.
Cisco adaptive security appliances are shipped with a factory-default configuration that enables quick startup. The ASA 5505 comes preconfigured with. Two Vlans: VLAN1 and VLAN2. VLAN 1 has the following properties: - Named 'inside' - Allocated switch ports Ethernet 0/1 through Ethernet 0/7 - Security level 100 - IP address of 192.168.1.1 255.255.255.0. VLAN2 has the following properties: - Named 'outside' - Allocated switch port Ethernet 0/0 - Security level of 0 - Configured to obtain its IP address using DHCP This is why I thought it would be VLan1. Also, with Vlan2 getting its ip from dhcp, it might get it from the Checkpoint firewall.
Also, with it connected to our subnet, it might start suppying IPs with its own dhcp server:O What do you think? Hmm, no it doesn't need to. Can you post your config here? To do that, you need to record the sh run to a text file in hyperterminal.
You'll go to Transfer/Capture Text, give it a name, and it will start to record. Then at the ASA# prompt type show run and hit spacebar all the way until you get back to the ASA# again. Then you click Transfer/Capture Text/Stop From the sound of it, it doesn't sound like the ASA is configured for any public access yet, so you should just be able to post the config here without modifying it. Just double check there are no public addresses in the config for your security. Here's the link copied from by browser: And here is the run shown: show run: Saved: ASA Version 7.2(3)! Hostname ciscoasa enable password encrypted names!
Interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0! Interface Vlan2 nameif outside security-level 0 ip address 192.168.10.11 255.255.255.0! Interface Ethernet0/0 switchport access vlan 2! Interface Ethernet0/1! Interface Ethernet0/2! Interface Ethernet0/3!
Interface Ethernet0/4! Interface Ethernet0/5! Interface Ethernet0/6! Interface Ethernet0/7! Well, a couple of things: Is your workstation that you're trying to connect to the ASA with on the 192.168.1.0 network, or is it on the 192.168.10.0 network? If it's on the latter, you should connect your workstation to the back of the ASA and put your workstation statically on the 192.168.1.0 network. This will get you into it.
If you are trying to connect to it from the 192.168.10.0 network, you'll have to issue: ASA# config t ASA(config)# http 192.168.10.0 255.255.255.0 outside See if that works. You won't be able to ping 192.168.1.1 from the 192.168.10.0 side. ASA doesn't support pinging the opposite side of the device (from outside interface to inside). You can either ping the outside or inside, or through the device to another host on the inside from the outside.